多项选择题

YourcompanywantsServer1 eth0（vNIC1）configuredsothatital……

Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？（）

A. The fabric interconnects must be in end-host mode.
B. A pin group must be configured on the server tab in Cisco UCS Manager.
C. In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.
D. Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.
E. Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.

<上一题目录下一题>

热门试题

单项选择题Refer to the exhibit. The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）

A. Fix the port channel configuration between Fabric Interconnect B and Nexus 5548 B as the port channel IDs do not match.
B. Modify the bridge priority on the fabric interconnects so that one of the Nexus 5548s will always be the root bridge.
C. Modify the bridge priority on the Nexus 5548s so that one of them will always be the root bridge.
D. Modify the port priorities on the fabric interconnect uplinks （Paths B and C） so that they are a higher priority than ports Eth1/4 and Eth1/9 （Path D）.
E. This is an invalid configuration as Cisco UCS fabric interconnects cannot be directly connected.

单项选择题Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）

A. A is an uplink port， B is a fabric port， C is a server port， D is a backplane port， E is a DCE interface， and F is a vNIC
B. A is an uplink port， B is a server port， C is a fabric port， D is a backplane port， E is a DCE interface， and F is a vNIC
C. A is an uplink port， B is a fabric port， C is a backplane port， D is a server port， E is a DCE interface， and F is a vNIC
D. A is an uplink port， B is a server port， C is a fabric port， D is a DCE interface， E is a backplane port， and F is a vNIC
E. A is an fabric port， B is a downlink port， C is an uplink port， D is a server port， E is a VIC interface， and F is a vNIC

多项选择题Refer to the exhibit. Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）

A. Cisco UCS 6148， Cisco UCS 6248UP， or the Cisco UCS 6296UP fabric interconnects
B. Cisco UCS 2104XP Fabric Extender
C. Cisco UCS 2204XP or 2208XP Fabric Extenders
D. Cisco UCS M81KR Virtual Interface Card
E. Cisco UCS Virtual Interface Card 1280
F. Cisco UCS Virtual Interface Card 1240 with a port expander

多项选择题WhatisrequiredforCiscoUCSC-SeriesrackserverintegrationwithCiscoUCSManager？（）

A. Cisco UCS Manager 1.3（xx） or later and a pair of Nexus 2248 FEXes
B. Cisco UCS Manager 2.0（2xx） or later and a pair of Nexus 2232 FEXes
C. Two Cisco UCS 6100 Series or 6200 Series fabric interconnects
D. Two RJ45 Ethernet cables
E. The fabric interconnects must be in end-host mode

多项选择题ACiscoUCSfabricinterconnectinend-hostmodelearnsMACaddressesonwhichporttypes？（）

A. Uplink Ethernet ports or border ports
B. Appliance ports
C. Server ports
D. Fabric ports
E. Backplane ports
F. vEth interfaces
G. A Fabric Interconnect doesn’t learn MAC addresses in End Host mode. Pinning is used instead.