A.14.7MpaB.16.2MpaC.17Mpa
单项选择题氧气在室内积聚其体积浓度超过()时,有发生火灾的危害,因此在堆积氧气瓶的仓库应设有通风装置。
A.0.05B.0.1C.0.23
单项选择题氧(O2)是双原子气体,密度比空气(),在标准状况下,每立方米氧重1.429㎏。
A.轻B.相等C.重
单项选择题氧气切割废钢中碳含量为()%,冬季切割厚废钢时,需加热至150℃。
A.<0.6B.0.6-0.8C.0.8-1.1
单项选择题废钢中()含量通常较低,对气割无影响,反之会使切割速度降低。
A.C(碳)B.Mn(锰)C.S(硫)
单项选择题一般结构钢因主要成份是铁,也是()加工的主要对象。
A.氧气切割B.氧熔剂切割C.氧矛切割
单项选择题在气割中,金属的热导率(),否则预热火焰热和燃烧反应热会被迅速导散,使气割过程不能开始或中途停顿。
A.不能太高B.不能太低C.适中
单项选择题在氧气切割时,金属的燃点()它的熔点,否则金属在达到燃点前就被熔化了,达不到气割的目的。
A.高于B.等于C.低于
单项选择题氧气切割大厚度废钢时,熔渣中()的成份最多。
A.Fe3O4B.Fe2O3C.FeO
单项选择题预热火焰的二次焰流(),切割氧流的有效长度就大,所能切割的厚度也越厚。
A.越长B.越短C.适中
单项选择题当需要一定的切割精度和高速度,而材料的品种较多时,则以()切割法较为合适。
A.氧气切割B.等离子弧切割C.激光切割
单项选择题氧气切割碳素钢、低合金钢切割面上缘熔化度()。
A.很小B.较大C.不大
单项选择题氧气切割碳素钢、低合金钢切口宽度一般为()。
A.0.2-0.8mmB.2.5-5.0mmC.1.5-2.5mm
单项选择题氧气切割适应切割材料为()。
A.低碳钢、低合金钢、不锈钢、铝及其它合金B.不锈钢、低合金钢、所有非金属材料(陶瓷、塑料等)C.碳素钢、低合金钢
单项选择题氧气切割方法的功率密度和切割废钢的最大厚度为()。
A.106-109w/cm2、80mmB.105-106w/cm2、200mmC.5-104w/cm2、400mm
单项选择题氧气的切割原理就是()。
A.利用可燃气体加上助燃气体通过一特别的割矩,使它发生剧烈的氧化-燃烧,利用燃烧所产生的热量来熔化工件B.先借预热火焰将切割区预热至燃点后,用直径3-12mm厚壁碳素钢管在管内供送切割氧,使废钢在氧中燃烧进行切割或穿孔的一种特殊气割方法C.就是在切割氧流中,添加铁粉等熔剂借铁粉的燃烧补充切割所需的热量,实现气割