A.0.09% B.0.1% C.1.0%
单项选择题线能量与焊接电流和焊接电压成正比,与()成反比
A.焊接速度 B.工件厚度 C.焊条直径
单项选择题发生角变形的根本原因是()
A.横向收缩变形在厚度方向上的不均匀B.选择焊接方法不当C.金属不同组织的热膨胀系数不同
单项选择题焊接线能量,又称热输入,其数值等于电流乘电压除以()
A.单位焊缝长度 B.焊接时间 C.焊接速度 D.单位焊缝宽度
单项选择题埋弧自动焊进行下坡焊时焊缝()和余高减小,焊缝宽度增加
A.厚度 B.金属熔敷量 C.成形系数 D.抗拉强度
单项选择题弧长调节系统的作用是当弧长变化时,能立即调整()和焊丝熔化速度之间的关系,使弧长恢复至给定值.
A.送丝速度 B.焊接速度 C.机头位置 D.焊剂堆敷高度
单项选择题焊缝中夹杂物是由于焊接冶金反应形成的。焊接时,由于熔池的结晶速度较快,一些脱氧、脱硫产物来不及聚集逸出就残存在焊缝中形成()
A.裂纹 B.偏析 C.夹杂 D.气孔
单项选择题对电源没有接地中线的低压电网中的用电器,将用电器的外壳用导体线作地连接以保护人身安全,叫()
A.防触电装置 B.防雷保护 C.防护装置 D.保护接地
单项选择题防止冷裂纹措施有选用()焊条:焊条、焊剂严格按定烘:提高焊缝金属的塑性:选择合理的焊接工艺:改善结构的应力状态.降焊接应力
A.酸性 B.低氢型 C.马氏体不锈钢 D.铁素体不锈钢
单项选择题金属材料在拉伸时产生屈服现象时的应力称为()
A.屈服点 B.伸长率 C.断面收缩率 D.抗拉强度
单项选择题焊接结构焊接后会产生焊接残余应力,容易导致产生(),因此重要的焊接结构焊后应该进行消除应力退火处理
A.气孔 B.裂纹 C.夹渣 D.未焊透
单项选择题在有泥、()、湿木板、钢筋混凝土铺设地面的环境是属于触电的危险环境
A.橡胶 B.砖 C.沥青 D.瓷砖
单项选择题等离子弧切割毛刺的形成主要与()有关
A.切割电流和工作电压 B.保护气流量和空载电玉 C.气体流量和切割速度 D.切割电流和空载电压
单项选择题焊条电弧焊钢板对接横焊盖面焊时,采用连弧()
A.多层焊 B.多道焊 C.单道多层焊 D.多到多层焊
单项选择题C02悍短路过渡是在采用细焊丝、(),低电弧电压接时出现的
A.大电流 B.小电流 C.高速迭丝 D.陡降外特性电源
单项选择题单道焊、大电流慢速摆动焊法,由于()大,高温停留时间长,使焊缝和过热区晶粒粗大,导致塑性和韧性下降,还可能产生焊缝中心线裂纹
A.焊接线能量 B.焊件厚度 C.坡口角度 D.熔池金属重量