多项选择题

Exhibit SW1#show spanning-tree vlan 200 VLAN200 Spannin……

Exhibit
SW1#show spanning-tree vlan 200
VLAN200
Spanning tree enabled protocol iee
eRoot ID Priority 32968
Address 000c.ce29.ef00
Cost 19
Port 2 （FastEthernet0/2）
Hello time 10 Sec Max Age 20 sec Forward Delay 30 sec
Bridge ID Priority 32968 （priority 32768 sys-id-ext 200）
Address 000c.ce2a.4180
Hello Time 2 sec Max Age 20 Sec Forward Delay 15 sec
Interface Role Sts Cost PrioNbr Type
Fa0/2 Root FWD 19 128.2 P2p
Fa0/3 Altn BLK 19 128.3 P2p
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statementsabout the STP process for VLAN 200 are true？（）

A.BDPUs will be sent out every two seconds
B.The time spent in the listening state will be 30 seconds
C.The time spent in the learning state will be 15 seconds
D.The maximum length of time that the BPDU information will be saved is 30 seconds
E.This switch is the root bridge for VLAN 200
F.BPDUs will be sent out every 10 seconds

<上一题目录下一题>

热门试题

单项选择题Iftherootbridgefails，configurationBPDUswillnolongerbesent.WhichSTPtimerwillhavetoexpirebeforetheotherswitchescanactivelyrestoreconnectivitywithtopologychangeprocedureofSTP？（）

A.hello timer
B.BPDU timer
C.Forward_delay timer
D.Max_age timer
E.Dead timer
F.Wait timer

多项选择题Given the above diagram and assuming that STP is enabled on all switch devices， which twostatements are true？（）

A.DSW11willbe elected the root bridge
B.DSW12 will be elected the root bridge
C.ASW13 will be elected the root bridge
D.P3/1 will be elected the nondesignated port
E.P2/2 will be elected the nondesignated port
F.P3/2 will be elected the nondesignated port

问答题Refer to the output shown on switch SW1 below： Warning： Spantree port fast start should only be enabled on ports connected to a single host.Connecting hubs， concentrators， switches， bridges， etc. to a fast start port can cause temporaryspanning tree loops. Use with caution. Spantree ports 4 1-24 fast start enabled. What command could you enter to reproduce this output？

问答题Refer to the output shown on switch SW1 below： VLAN 1 bridge priority set to 8192. VLAN 1 bridge max aging time set to 20.VLAN 1 bridge hello time set to 2. VLAN 1 bridge forward delay set to 15. Switch is now the root switch for active VLAN 1. What command would you enter to reproduce this output？

单项选择题Exhibit： Assuming that VLAN 1 and VLAN 2 traffic is enabled on the above network， what effect will thefollowing command have when entered on port 0 2 on switch SWA？（） spanning-tree vlan 1 port-priority 16

A.VLAN 1 traffic will be blocked on Switch SWB port 1/1
B.VLAN 2 traffic will be blocked on Switch SWB port 1/1
C.VLAN 2 traffic will be blocked on Switch SWA port 0/2
D.VLAN 1 and 2 traffic will be blocked on Switch SWA port 0/1
E.VLAN 1 and 2 traffic will be blocked on Switch SWA port 0/2