多项选择题

A. Hash address： Selects the server by using a hash val……

Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？（）

A. Hash address： Selects the server by using a hash value based on either the source or destination IP address， or both
B. Hash URL： Selects the server by using a hash value based on the requested URL
C. Hash MAC.Selects the server by using a hash value based on either the source or destination MAC address， or both
D. Hash header： Selects the server by using a hash value based on the HTTP header name
E. Hash IP： Selects the server using a hash value based on the IP address

<上一题目录下一题>

热门试题

单项选择题FromtheCiscoUCSCLI，howdoyouverifywhichuplinkportsabladeserverisusingforitsnetworkconnectivity？（）

A. UCS-A# show pinning border-interfaces
B. UCS-B# show service-profile circuit
C. UCS-B（nxos）# show pinning server-interfaces
D. You must statically configure which uplink the blades should use， or you will not have connectivity.

单项选择题WhatinterfaceiscreatedwhenanFCPortChanneliscreatedonaCiscoUnifiedComputingSystem？（）

A. An interface ’san-port-channel’ in NXOS
B. An interface ’port-channel’ in NXOS
C. An interface ’port-channel’ with ’mode fc’ configured
D. An interface ’fc-port-channel’ in NXOS

多项选择题YourcompanywantsServer1 eth0（vNIC1）configuredsothatitalwaysusesFabricInterconnectAPortChannel1（Po1）whenitcommunicateswithanythingoutsideoftheCiscoUCSdomain.However，ifvNIC1failsovertoFabricInterconnectBusingfabricfailover，thenvNIC1cananyuplinkportonFabricInterconnectB.Whichstatementsaretrue？（）

A. The fabric interconnects must be in end-host mode.
B. A pin group must be configured on the server tab in Cisco UCS Manager.
C. In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.
D. Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.
E. Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.

单项选择题Refer to the exhibit. The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）

A. Fix the port channel configuration between Fabric Interconnect B and Nexus 5548 B as the port channel IDs do not match.
B. Modify the bridge priority on the fabric interconnects so that one of the Nexus 5548s will always be the root bridge.
C. Modify the bridge priority on the Nexus 5548s so that one of them will always be the root bridge.
D. Modify the port priorities on the fabric interconnect uplinks （Paths B and C） so that they are a higher priority than ports Eth1/4 and Eth1/9 （Path D）.
E. This is an invalid configuration as Cisco UCS fabric interconnects cannot be directly connected.

单项选择题Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）

A. A is an uplink port， B is a fabric port， C is a server port， D is a backplane port， E is a DCE interface， and F is a vNIC
B. A is an uplink port， B is a server port， C is a fabric port， D is a backplane port， E is a DCE interface， and F is a vNIC
C. A is an uplink port， B is a fabric port， C is a backplane port， D is a server port， E is a DCE interface， and F is a vNIC
D. A is an uplink port， B is a server port， C is a fabric port， D is a DCE interface， E is a backplane port， and F is a vNIC
E. A is an fabric port， B is a downlink port， C is an uplink port， D is a server port， E is a VIC interface， and F is a vNIC