A.10mm/sB.20mm/sC.30mm/sD.40mm/s
单项选择题当压实度现场实测值出现有超过规定极值时,应按下列()方法处理。
A.按未超过规定极值点数计算合格率B.当平均值大于设计值时,按规定计算合格率C.当平均值大于规定极值时,按规定计算合格率D.返工处理
单项选择题现场试验数据表明,当标定罐深度每增加()时,量砂的松方密度增加0.15%左右,对现场测试结果无实质影响。
A.2cmB.3cmC.4cmD.5cm
单项选择题落锤式弯沉仪法与贝克曼梁法相关性试验中,两种仪器对同一点弯沉测试的时间间隔不应超过()min。
A.5B.10C.15D.20
单项选择题连续式平整度仪测试路面平整度时,人工采集间距为()。
A.0.5mB.1.0mC.1.5mD.2.0m
单项选择题连续式平整度仪自动采集间距为()cm。
单项选择题灌砂法检测压实度时,若发现储砂筒内砂不足以填满试坑时,以下正确的做法是()。
A.立即往储砂筒添加砂量B.关闭锥体漏斗然后再添加砂量C.选择更大尺寸的灌砂筒重新试验D.以上全部的不对
单项选择题在沥青路面施工过程中,当沥青混合料尚未冷却时,可用大改锥插入至沥青层地面深度后用尺读数量取沥青层厚度,测定结果()。
A.以cm计,精确至1cmB.以cm计,精确至0.1cmC.以mm计,精确至1mmD.以mm计,精确至0.1mm
单项选择题下列有关挖坑法和钻芯法试验填补说法中,正确的是()。
A.对无机结合料稳定层及水泥混凝土路面板,应按相同配合比用新拌的材料分层填补并用小锤压实B.对无结合料粒料基层,可用挖坑时取出的材料,适当加水拌和后分层填补,并用小锤压实C.对正在施工的沥青路面,用相同级配的热拌沥青混合料分层填补,并用加热的铁锤或热夯压实,旧路钻孔也可用乳化沥青混合料填补D.所有补坑结束时,应与原面层填平,用重锤或压路机压实平整
单项选择题采用钻孔法测试路面厚时,不适用于()的检测。
A.沥青面层厚度B.能够取出完整芯样的基层厚度C.砂石路面厚度D.水泥混凝土路面板厚度
单项选择题根据《公路路基路面现场测试规程》(JTG 3450-2019),挖坑法适用于()。
A.沥青面层厚度B.能够取出完整芯样的基层路面厚度C.水泥混凝土路面板厚度D.砂石路面厚度
单项选择题下列四个选项中,()不是路面结构层厚度的规定测试方法。
A.挖坑法B.钻芯法C.短脉冲雷达测试法D.水准仪量测法
单项选择题将落锤式弯沉仪牵引至测试点过程中,牵引车的行驶速度不宜超过()km h。
A.30B.40C.50D.60
单项选择题在测定某路面渗水系数时,水面在100mL刻度时,开始计时,计时3min后立即记录水量,水面在430mL,则该路面的渗水系数为()mL min。
A.33.3B.110C.133.3D.143.3
单项选择题刚性管道沟槽回填石灰土类垫层压实度检测时,检测频率应为每()m,每层每侧一组。
A.50B.100C.200D.500
单项选择题挖坑灌砂法压实度测定时,粗粒土含水率测定用电子天平分度值为()。
A.0.01gB.0.1gC.1.0gD.10g