A.3~5min B.5~15min C.15~30min D.30~45min E.45~60min
单项选择题在铸型焙烧时,磷酸盐包埋材料在()维持15~30min可获得更大的热膨胀。
A.200℃ B.300℃ C.400℃ D.500℃ E.600℃
单项选择题包埋时液体加入过少则()
A.包埋材料较稀,材料的膨胀减小 B.包埋材料较稀,材料的膨胀增大 C.包埋材料较稠,材料的膨胀减小 D.包埋材料较稠,材料的膨胀增大 E.包埋材料较稠,材料的膨胀不变
单项选择题包埋时液体加入过多则()
单项选择题包埋材料的膨胀总量中不包含()
A.热膨胀 B.凝固膨胀 C.吸湿膨胀 D.铸件膨胀 E.蜡熔模膨胀
单项选择题关于包埋铸型的说法中,不正确的是()
A.根据包埋材料凝固后与铸型成型器能否分离可分为有圈铸型及无圈铸型 B.有圈铸型时,包埋材料能自由膨胀,可以较好的补偿铸金的收缩 C.有圈铸型时,膨胀力可能会向内指向铸模,造成铸件变形、破裂 D.有圈铸型时,多采用在铸圈内放置石棉、瓷纸、纤维素作为内衬,同时在铸圈两端各留出3~5mm的长度 E.无圈铸型可获得自由的材料膨胀,一般在包埋材料凝固后即可分开
单项选择题包埋材料调拌时间不宜过长,这是因为过度调拌会()
A.减少包埋材料的热膨胀 B.增加包埋材料的热膨胀 C.增加包埋材料内的气泡 D.降低包埋材料的强度 E.增加包埋材料的脆性
单项选择题关于包埋材料的性能的说法中,错误的是()
A.有足够的膨胀来补偿铸金的凝固收缩 B.注水以后不会发生膨胀 C.能承受高温及铸造时的压力 D.能清晰、精确的复制熔模的细微结构 E.有良好的透气性
单项选择题在磷酸盐材料即将结固之前注水,可获得一定的膨胀,这是()
A.蜡型膨胀 B.吸水膨胀 C.凝固膨胀 D.金属膨胀 E.化学膨胀
单项选择题由于包埋材料正常的结晶增长引起的膨胀属于()
单项选择题关于包埋的说法中,错误的是()
A.附着在熔模组织面的气泡会直接影响到修复体的精度 B.包埋过程中附着在熔模磨光面的气泡可能会影响到修复形态细微结构 C.液体过多,则包埋材料的吸水膨胀减小 D.液体过少,包埋材料流动较差,易将空气包裹在材料中 E.采用真空调拌与灌注,可最大限度的防止气泡的混入
单项选择题非真空包埋有约()没有气泡。
A.2℅ B.7℅ C.12℅ D.17℅ E.22℅
单项选择题真空包埋可达到()没有气泡。
A.75℅ B.80℅ C.85℅ D.90℅ E.95℅
单项选择题包埋的时候粉液比例不当,如液体过少,则()
A.包埋材料的热膨胀减小 B.包埋材料的凝固膨胀增大 C.包埋材料的吸水膨胀减小 D.包埋材料流动则较差,包埋时易将空气包裹在材料中 E.空气在调拌时更容易混入包埋材料,在包埋过程中附着在熔模表面
单项选择题包埋的时候粉液比例不当,如液体过多,则()
A.包埋材料的热膨胀减小 B.包埋材料的吸水膨胀减小 C.包埋材料的凝固膨胀增大 D.包埋材料流动则较差,包埋时易将空气包裹在材料中 E.空气在调拌时更容易混入包埋材料,在包埋过程中附着在熔模表面
单项选择题在包埋过程中出现气泡,可能出现的结果中,错误的是()
A.影响到修复体的细微形态结构 B.影响到与对颌牙、邻牙的接触关系 C.直接影响到修复体的精度 D.造成制作失败 E.导致铸圈加热升温过快