A.0.5B.0.7C.0.9D.1.0
单项选择题YB25内衬纸内侧长边折叠器和内侧短边折叠器与二号轮外壁相距2mm,外侧折叠板与二号轮外壁相距2.5mm,内侧折叠板与二号轮外壁相距()mm。
A.1B.2C.3D.4
单项选择题FCOKE350包装机内框纸剪切机构完成内框纸的切割、分离、折边和输送,()记录有缺陷信号的小盒将不供给内框纸,由剪切机构内的压缩空气喷嘴将其吹掉。
A.传感器B.移位寄存器C.光电检测器D.电磁铁
单项选择题YB45型硬盒包装机内框纸的前定位导板与内框纸应相距()mm。
A.0.01B.0.1C.0.02D.0.2
单项选择题YB45型硬盒包装机内框纸吸臂在()时,需完全与内框纸对中。
A.后退行程始点B.前退行程始点C.后退行程终点D.前进行程终点
单项选择题YB45型硬盒包装机内框纸吸臂在后退行程终点时,需完全与内框纸对中,并与()有平行度要求和距离要求。
A.切刀B.定位块C.输送平面D.四轮端面
单项选择题FOCKE350包装机内框纸横向输送带的定位调整:盘车直至内框横向输送带处于()位置为止,内框纸应被完全推入第二往复盒内,并有0.5~1mm的间隙。
A.运动B.停顿C.平行D.垂直
单项选择题YB25软盒包装机封签纸库支座材质是(),纸库座固定在机器箱体上。
A.铸铁件B.铸钢件C.锻铝件D.铸铝件
单项选择题YB25软盒包装机将预切式封签放在纸库里面,通过扇形吸纸轮将封签取出纸库后,扇形轮边()转动边移动,将封签送入输送通道部分。
A.顺时针B.逆时针C.定向D.反向
单项选择题YB25软盒包装机封签纸库调整完毕后,应检查()在转动时不能与封签纸库干涉。
A.封签输送轮B.封签吸纸轮C.封签接纸轮D.封签上胶轮
单项选择题YB25软盒包装机封签纸库应与封签分离板对中,应保证()相交于封签纸库的导板面和封签分离板的平台。
A.封签分离刀B.封签纸C.封签吸纸轮D.封签接纸轮
单项选择题YB25软盒包装机通过调整()基座上的螺钉,使封签输送两导轨之间距离为0.8mm。
A.封签胶缸B.离合器C.第一导纸辊D.封签上胶轮
单项选择题YB25软盒包装机当封签扇形吸纸轮回转轴摆动至最右端位置时,扇形齿轮与齿条均应是()齿牙进行啮合,且此时摇臂不允许处于垂直向上的位置。
A.最后一个B.第一个C.第二个D.中间一个
单项选择题手动盘车YB25软盒包装机到封签定位器处于最前位置,通过封签定位器上的螺钉,调整封签定位器与()处于对中位置。
A.封签胶缸B.输送通道C.封签输送辊D.导板
单项选择题FOCKE350硬盒包装机商标纸库三个料位可以自动转换,转换机构的动力由电机独立驱动,而电机受控于商标纸料位()的相对位置。
A.电感探头B.检测探头C.光电探头D.光纤探头
单项选择题下列关于FOCKE350硬盒包装机商标纸库叙述不正确的是()
A.FOCKE350型硬盒包装机商标纸库共有三个储料位,每个料位约能存储5000张商标纸B.FOCKE350型硬盒包装机商标纸库三个料位可以自动转换C.FOCKE350型硬盒包装机商标纸库料位转换机构的动力由电机独立驱动D.FOCKE350型硬盒包装机商标纸库料位自动转换机构的动力由电机独立驱动,其电机受控于商标纸料位检测探头的相对位置